FAQ#007 – Are the TEL-310S CUS control unit and the PWS power unit supplied with the fixing kit?
No kit is needed. The “CUS” and “PWS” units are placed in aluminum boxes ready to be fixed on the wall through four M6 screws (not included).
FAQ#006 – Is it possible to use the ANS adjustable support for the pendulum optical manual readout (coordinometer)?
The pendulum readout fixing plate has four holes so it can be fixed, through screws, to the “ANS” adjustable support.
FAQ#005 – Is it possible to fix the ANS adjustable support to the floor?
Since the “ANS” support is articulated, it can be fixed to the floor; this can be useful in case the pendulum’s wire is too far from the walls.
FAQ#004 – Is it possible to place the SUS optical sensor unit with the X axis perpendicular to the wall where the ANS support is fixed?
The TEL-310S telecoordinometer has the following measuring range: To use the “ANS” adjustable support you must have the “X” axis parallel to the wall: so it is not possible to fix the “SUS” optical sensor unit perpendicular to the wall using the “ANS” adjustable support.
FAQ#003 – Which are the needed conditions to use the ANS adjustable support for TEL-310S if you need to monitor the direct pendulum’s wire?
To fix the “SUS” optical sensor unit through the “ANS” support, it is necessary that the direct pendulum’s wire is at a distance of d=230 mm. from the wall. To achieve that, the direct pendulum’s tank has to be placed at a distance of D=20 mm. from the wall: in this way is guaranteed that […]
FAQ#002 – What is the 0TEL310ANS0 adjustable support for TEL-310S and what is it for?
The “ANS” adjustable support (0TEL310ANS0) has been developed to support and fix the “SUS” optical sensor unit (0TEL310SUS0) of the new TEL-310S telecoordinometer. The support is fixed to the wall through two M16 threaded bars, of 370 mm. length (supplied). Once the “SUS” optical sensor unit is fixed to the support, it is possible to […]
FAQ#001 – If the SUS optical sensor unit is removed for maintenance, is it possible to continue the monitoring using the pendulum optical manual readout?
It is possible to use the pendulum optical manual readout instead of TEL-310S “SUS” optical sensor unit without any regulation of the “ANS” support. It is also possible to start the pendulum’s monitoring with the pendulum optical manual readout and then automate the readings with TEL-310S telecoordinometer , without changing its initial zero.
V-NOTCH and Flow Meters
V-NOTCH and Flow Meters Reference products codes: QV, QVML, QVLIV, P252Q Water flow monitoring in open channels is widely employed in environmental and geotechnical field. Leakage measurement is one of the most important indicator of the overall performance of earth/rock-fill and concrete dam. The leakage rate is a function of the water level in the reservoir and […]
Water level meters, Staff gauges
Water level meters, Staff gauges Reference products codes: C112, C112T, HIDR Dipmeters are used for water ground level measurements in standpipes, wells and Casagrande piezometers. It is a battery powered portable device equipped with a dipping probe connected to a graduated cable wrapped on a cable reel. In contact with water the dipping probe activates either an audible […]
Casagrande and standpipe piezometers
Casagrande and standpipe piezometers Reference products codes: P101, P112, P112A, TCH, TFHCasagrande filter unit is used to measure the water pressure in permeable soil. Filter unit is made in syntherised high density polyethylene. It is available in different models to suite all the customer applications. Filter units have threaded cap joint with two 0.5″ twin […]
Drive-in piezometers
Drive-in piezometers Reference products codes: PK45I, P235I Drive-in piezometers, also called push-in piezometers, are designed for installation in soft clays, organic or fine grained cohesionless soils. The piezometers are pushed directly into the soil using conventional cone penetrometer or drilling rods with adapters. The large diameter nose cone decreases the chance of overpressure while the piezometer is […]
Titanium piezometers
Titanium piezometers Reference products codes: P235TI Piezo-resistive titanium piezometers are designed to operate in corrosive environments, such as salt water, tailings, and landfills. Resistance to corrosion is provided by a titanium body, ceramic diaphragm, polyethelene or ceramic filter, and acid-resistant signal cable. The robust 4-20mA output is compatible with most readouts (as CRD-400) and data loggers and is […]
