FAQ#082 – Is there any precaution to adopt for the number of measurements saved on the OMNIAlog / miniOMNIAlog memory?
OMNIAlog is equipped with a microSD 2GB memory. This memory allows to save a very high number of readings. For this reason, it is necessary to bear in mind what follows: Therefore SISGEO strongly suggests to periodically download data and, later, to delete them from OMNIAlog memory. This way it is guaranteed an efficient data download.
FAQ#080 – What dimensions has the .CSV file in columns that contains the measures acquired with OMNIAlog and miniOMNIAlog?
The dimensions of the measures file “in columns” downloaded with OMNIAlog and miniOMNIAlog vary according to the number of sensors acquired and the stored cycles of acquisition. The higher is the number of sensors acquired and the number of cycles of acquisition stored, bigger is the dimension of the file. It could be used the […]
FAQ#079 – Is it possible to send SMS in case of alarms with miniOMNIAlog?
Yes, if miniOMNIAlog is equipped with 2G (GSM/GPRS) modem. To do so, the user must have already configured the relative web pages.
FAQ#078 – Is it possible to send SMS in case of alarms with OMNIAlog?
Yes, if OMNIAlog is equipped with a 2G (GSM/GPRS) modem, connected through a serial cable to its RS232 port. OMNIAlog allows to set up alarm thresholds and the notification of these alarms could occur: – by SMS; – by email; – by FTP; – increasing the acquisition frequency; – managing a digital output (for example to manage […]
FAQ#076 – Why it is necessary add a termination resistor to the last digitized sensor of each RS-485 chain?
All SISGEO digitized instruments (IPIs, Tiltmeters, H-Level…) use the RS-485 serial communication protocol The RS485 protocol contemplate a termination resistor. The recommended chain connection is point-to-point (multidropped) nodes as a bus mode (line). Star, ring or multiply network connection are not recommended. SISGEO dataloggers has already a termination resistor assembled (typically 120Ω). On the opposite […]
FAQ#074 – Which kind of datalogger is necessary to read a SISGEO digital sensors?
The sensors are read connecting the end cable to a Modbus Master unit (i.e. OMNIAlog or miniOMNIAlog) with RS-485 interface (DCE, Half duplex, no Echo) able to manage communication with SISGEO Modbus RTU communication protocol. SISGEO’s communication protocol is available for the release upon request. The power [W] of power supply must be chosen according […]
FAQ#073 – Which is the maximum number of digitized sensors (RS-485, Modbus), the maximum number of chains and the maximum length of cable in a RS-485 network?
Last update: October 2021 All the SISGEO digitized sensors utilize a RS485 interface with Modbus protocol. 1.The maximum number of digitized sensors in a RS-485 network are 247 (theoretical) 2.The maximum number of digitized sensors chains that is possible to connect to Modbus master unit (as OMNIAlog or miniOMNIAlog) are 4. 3. About the maximum […]
FAQ#072 – Why pushing RUN in a miniOMNIAlog webpage with 3G/2G modem the local connection with the PC gets lost?
The loss of the local connection with the PC is normal. This happens because the communication “bus” is the same between PC and miniOMNIAlog and between miniOMNIAlog and 3G/2G modem. Therefore, if you start miniOMNIAlog from the web, the communication is directed towards the 3G/2G modem. This allows to the modem to send SMS, e-mail […]
FAQ#071 – Why miniOMNIAlog is supplied through the PC when it is connected through USB?
This feature allows to not consume the internal batteries during the configuration phase or during the data download. In this way, independently from the duration of the activities above described, the internal batteries are used only during the field activities (acquisition, data dispatch etc). This guarantees a superior duration of exercise.
FAQ#070 – If you disconnect the USB cable from miniOMNIAlog, the datalogger resets. Is it normal?
Yes, it is. This takes place because when you connect the PC though USB connection, miniOMNIAlog is powered by the PC. If you disconnect the USB cable, miniOMNIAlog resets to change its supply source and returns to the supply through internal battery or from an external source (solar panel or electrical supply).
FAQ#069 – If miniOMNIAlog is supplied with internal batteries, can it read the digitized sensors SISGEO?
No, in case you have to read the SISGEO digitized sensors, it is necessary to use an additional module of power supply (code 0OMX24V030W). This is necessary to power the instrument with the necessary power supply. This module considers the supply or from solar panel or electrical.
FAQ#068 – Using miniOMNIAlog, is it possible to do acquisitions leaving it connected to the PC?
No, it is not possible. miniOMNIAlog, to do correct measurements, needs to be powered or from the internal battery or from an external power supply (solar panel, electrical supply) to supply to the connected instruments the right tension and current. Leaving connected miniOMNIAlog to the PC through USB cable, the instrument is powered directly to […]
